The various tests discussed in this post involved a total of four different machines:
Some tests were conducted with MySQL 5.6.13-community, and other tests were conducted with Percona Server 5.6.13.
For this test, I looked at one of the most common ways of establishing a site-to-site link in the absence of a “true” VPN – the good old-fashioned SSH tunnel. I don’t have ready access to sufficient gear to set up a hardware-accelerated VPN, but this is enough to illustrate the point. Recall that the default SSL cipher suite used by MySQL/SSL is DHE-RSA-AES256-SHA; if we unpack this a bit, it tells us that we’re using Diffie-Hellman key exchange with SHA1 as our hashing function, RSA for authentication, and encryption with 256-bit AES (in CBC mode, according to the OpenSSL docs). Although perhaps not immediately obvious, this same cipher suite is pretty easy to emulate with OpenSSH. The SSH version 2 protocol uses DHE/RSA/SHA1 by default, so then all we need to do is explicitly specify the AES256-CBC cipher when we’re setting up our tunnel, and we should be, for all intents and purposes, comparing encrypted apples to encrypted apples. For the sake of curiosity, we also try our SSH tunnel with AES256 in CTR mode, which should theoretically be a bit faster due to its ability to encrypt blocks in parallel, but as it turns out, at least for this test, the difference is marginal.
The machines used for this test were machines C (server) and D (client), which are on the same VLAN of a gigabit Ethernet link, and the test script in use was similar to that from part 1, wherein we attempt to create 100 connections as fast as possible. Each test configuration was run 10 times, with the averages and standard deviations for each test listed in the table below, and the numbers are given in connections per second. Also, note that for this particular test, all keys used are 4096 bits and tests were run against Percona Server 5.6.13 only.
|NO ENCRYPTION||MySQL+SSL||SSH tunnel (AES256-CBC)||SSH tunnel (AES256-CTR)|
|1001.33 (59.26)||22.23 (0.1392)||476.52 (11.87)||482.02 (13.42)|
Or, for those of you who like graphics, I think the chart speaks for itself.
Obviously, not using encryption is still the fastest game in town, but connection throughput over an SSH tunnel doesn’t obliterate performance to anywhere near the same level as using MySQL’s native SSL capability. Going from 1000 cps to 22 cps is potentially unusable, but I’d venture a guess that 470-480 cps in a single thread would still provide serviceable results for most people.
Pursuit of data for this test came out of a question left in the comments on my original post; specifically, how the SSL connection penalty is impacted by increasing network latency. We can see from the results above that on a low-latency link, using SSL dramatically impacts performance, but what if we’re doing that connection over a WAN link? It might be the case that if we’re already paying a latency penalty due to simple round-trip time, maybe throwing encryption into the mix won’t hurt that much, even if we do it with MySQL’s built-in SSL support. Thus, for this test, I spun up two different Amazon EC2 instances (machines A and B, described above). Machine C, loacated in Northern California, was used as the client, and this test was conducted both with Community MySQL as well as Percona Server, and with key sizes ranging from zero to 4096 bits. The SSL cipher suite used was the default, and the test script the same as before – run 10 trials, create 100 connections as fast as we can, and report results in connections per second. However, for this test, the raw numbers are somewhat secondary; we’re really just looking to see the impact of network latency on SSL connection performance.
First, from C to B (Northern California to Ireland):
--- ec2-54-220-212-210.eu-west-1.compute.amazonaws.com ping statistics ---
50 packets transmitted, 50 received, 0% packet loss, time 49228ms
rtt min/avg/max/mdev = 167.851/170.126/177.433/2.289 ms
And next, from C to A (Northern California to Oregon):
--- ec2-54-212-134-221.us-west-2.compute.amazonaws.com ping statistics ---
50 packets transmitted, 50 received, 0% packet loss, time 49108ms
rtt min/avg/max/mdev = 42.543/44.648/59.994/3.194 ms
As expected, obviously the raw numbers are much lower for the transcontinental test than they are when connecting to servers that, at least geographically, are only a few hundred miles away, but as it turns out, with the exception of how Community MySQL behaves, which I’ll talk about in a minute, the percentage decrease in performance actually doesn’t really vary by that much. The table below compares connections from C to B with connections from C to A.
||MySQL 5.6.13 US->EU||MySQL 5.6.13 US->US||PS 5.6.13 US->EU||PS 5.6.13 US->US||PS 5.6.13-static US->EU||PS 5.6.13-static US->US|
A few comments on the above. First, at 1024 bits of SSL encryption, it doesn’t make that much difference if you’re 40ms away or 170ms away. Second, as latency decreases, the connection-throughput performance lost due to SSL encryption overhead increases. That makes sense, particularly when we consider that in the base cases (two servers on the same LAN, or connections over a TCP socket to the same server), connection throughput performance is dominated by the use (or not) of SSL. However, the one thing in all of this that doesn’t make sense to me is just how badly community MySQL fares with 4096-bit encryption compared to Percona Server. What’s so special about 4096-bit encryption that tanks the performance of Community MySQL but doesn’t seem to impact Percona Server nearly as much? I don’t have a good answer for this nor even a good hypothesis; if it hadn’t happened on both tests I’d probably have claimed a PEBCAT, but now I’m just not sure. So, if anyone else tries this test, I’d be curious to know if you get the same results.
Regardless of the anomaly with MySQL 5.6.13 and 4096-bit SSL, I think the primary takeaway from both this post and its predecessor is pretty clear: if you need end-to-end encryption of your MySQL traffic and you’re using replication or a connection-pooling sort of workload, MySQL’s built-in SSL support will probably serve you just fine, but if your application is of the type that requires setting up and tearing down large numbers of connections frequently, you might want to look at offloading that encryption work elsewhere, even if “elsewhere” just means running it through an SSH tunnel.